Selecting the right industrial gas burner is an important decision for original equipment manufacturers (OEMs) designing commercial and industrial heating equipment. Burner performance affects heating capacity, temperature control, combustion efficiency, equipment integration, and long-term system reliability.
Whether developing make-up air units, industrial ovens, process heating equipment, or custom HVAC systems, OEMs must evaluate several technical factors before choosing a gas burner.
Midco International provides gas burner solutions for commercial and industrial heating applications, helping equipment manufacturers identify combustion technologies suited to their specific operating requirements.
1. Heating Capacity and BTU Requirements
One of the first considerations when selecting an industrial gas burner is determining the required heating capacity.
Burners must provide sufficient heat input to meet the equipment’s operating demands without unnecessary oversizing.
OEMs should evaluate:
- Required BTU/hr input
- Desired operating temperature
- Airflow volume and temperature rise
- Heat losses within the equipment
- Minimum and maximum heating demand
- Expected operating conditions
An improperly sized burner may contribute to inefficient operation, temperature fluctuations, or difficulty maintaining desired heating conditions.
For make-up air applications, airflow and required temperature rise are especially important when calculating burner capacity.
2. Direct-Fired vs. Indirect-Fired Heating Applications
OEMs must determine whether their equipment requires direct-fired or indirect-fired heating.
Direct-Fired Gas Burners
Direct-fired systems introduce combustion heat directly into the process or supply airstream.
These systems are commonly used in certain make-up air units, industrial drying equipment, and process heating applications where direct-fired operation is appropriate.
Indirect-Fired Gas Burners
Indirect-fired systems transfer heat through a heat exchanger, keeping combustion products separate from the heated supply air.
These systems may be preferred when the application requires separation between combustion gases and the conditioned air.
The appropriate configuration depends on equipment design, air quality requirements, applicable codes, and the intended application.
3. Burner Modulation and Temperature Control
Temperature control is a critical factor in industrial heating equipment.
Some applications operate at relatively consistent heating demands, while others require frequent adjustments to maintain precise temperatures.
OEMs should consider whether their equipment requires single-stage, two-stage, or modulating burner operation.
Modulating burners can adjust heat input over an operating range, helping heating systems respond to changing demands.
Important considerations include burner turndown ratio, control compatibility, temperature stability, and minimum firing requirements.
Selecting the appropriate control method can help equipment manufacturers achieve consistent heating performance across varying operating conditions.
4. Combustion Airflow and Burner Configuration
Industrial gas burners must be compatible with the airflow characteristics of the equipment in which they operate.
Air velocity, pressure drop, combustion air availability, and burner placement can all affect performance.
For make-up air equipment, OEMs may need to evaluate push-through and pull-through configurations.
A push-through configuration generally places the fan upstream of the heating section, while a pull-through configuration places the fan downstream.
Each arrangement creates different operating conditions that must be considered during burner selection.
Proper airflow integration helps support stable combustion, reliable ignition, and consistent heat distribution.
5. Fuel Type and Gas Supply Requirements
Industrial gas burners must be selected according to the available fuel and gas supply conditions.
Natural gas and propane systems may require different burner configurations, components, and operating settings.
OEMs should review:
- Available fuel type
- Gas supply pressure
- Maximum and minimum firing requirements
- Gas train components
- Pressure regulation requirements
- Applicable fuel safety standards
Gas pressure that falls outside the burner’s specified operating range can affect ignition, combustion stability, and overall equipment performance.
Manufacturers should confirm fuel compatibility and required supply conditions before finalizing a burner design.
6. Burner Efficiency and Emissions Performance
Energy performance and emissions are increasingly important considerations in commercial and industrial heating equipment.
Burner design, combustion control, operating conditions, and system integration can influence fuel consumption and emissions.
OEMs should evaluate combustion performance across the intended firing range rather than relying only on maximum firing specifications.
Depending on the application, nitrogen oxide (NOx) emissions and other combustion-related requirements may influence burner selection.
Low-NOx burner technologies may be appropriate when equipment must satisfy specific emissions limits.
Manufacturers should review applicable environmental regulations and product performance documentation when selecting combustion equipment.
7. Equipment Size and Installation Requirements
Industrial heating equipment often has limited space available for burner installation.
OEMs must consider burner dimensions, mounting requirements, service access, and compatibility with existing equipment components.
Important integration factors include:
- Burner footprint and mounting orientation
- Combustion chamber dimensions
- Required clearances
- Electrical connections
- Gas train placement
- Airflow requirements
- Maintenance accessibility
Selecting a burner that fits the equipment’s mechanical design can help simplify manufacturing, installation, and future servicing.
8. Safety Controls and Industry Standards
Safety is a fundamental consideration in industrial gas burner selection.
Depending on the application, burner systems may require flame supervision, ignition controls, safety shutoff valves, airflow proving devices, temperature limits, and other protective components.
OEMs should evaluate the standards and codes applicable to their equipment.
For example, ANSI Z83.4, ANSI Z83.18, and ANSI Z83.25 address different categories of gas-fired heating equipment.
The applicable standard depends on the equipment’s intended use, design, and certification requirements.
Burner selection should be coordinated with the complete equipment safety system to support reliable operation and regulatory compliance.
9. Maintenance and Long-Term Reliability
Industrial gas burners are often expected to operate for extended periods under demanding conditions.
OEMs should consider serviceability and component availability when selecting a burner for their equipment.
A burner designed for accessible maintenance can help simplify routine inspections, cleaning, troubleshooting, and component replacement.
Long-term considerations include ignition reliability, flame detection, burner construction, operating environment, and replacement part availability.
Choosing equipment that supports practical maintenance can help reduce service complications throughout the heating system’s operating life.
10. Technical Support and OEM Integration
Industrial gas burner selection involves more than matching a burner to a BTU rating.
Equipment manufacturers may need assistance evaluating airflow, combustion requirements, controls, mechanical integration, and operating conditions.
Working with an experienced burner manufacturer can help OEMs identify potential design challenges before production.
Midco International offers commercial and industrial gas burner technologies for a range of heating applications.
By evaluating the complete heating system, OEMs can select combustion equipment that aligns with their performance, integration, and operating requirements.
Why Proper Industrial Gas Burner Selection Matters
A properly selected burner helps support the overall performance of commercial and industrial heating equipment.
The right solution must balance heating capacity, combustion characteristics, control requirements, safety, equipment dimensions, and maintenance considerations.
Selecting a burner based solely on maximum BTU input may overlook important operational factors.
For OEMs developing new equipment or updating existing designs, a comprehensive evaluation can help reduce integration problems and support dependable heating performance.
Frequently Asked Questions About Industrial Gas Burner Selection
How do OEMs determine the correct industrial gas burner size?
OEMs calculate heating requirements based on desired temperature rise, airflow, process demands, heat losses, and operating conditions. The burner must provide sufficient heating capacity while remaining compatible with the complete equipment design.
What is the difference between single-stage, two-stage, and modulating gas burners?
Single-stage burners generally operate at one firing rate, while two-stage burners provide two operating levels. Modulating burners adjust firing rates within a specified range to respond to changing heating demands.
Why is burner turndown ratio important?
Turndown ratio describes the relationship between maximum and minimum firing capacity. A wider operating range may help equipment maintain more consistent temperatures when heating demand varies, provided the burner and controls are properly matched to the application.
Can the same industrial gas burner be used for natural gas and propane?
Some burner models may support multiple fuel types through approved configurations or conversions. OEMs must verify manufacturer specifications and use the appropriate components and settings for the intended fuel.
What industries use industrial gas burners?
Industrial gas burners are used in commercial HVAC equipment, make-up air systems, industrial ovens, drying equipment, manufacturing processes, and other applications requiring controlled gas-fired heating.
How important is airflow when selecting a gas burner?
Airflow is essential because it affects combustion conditions, heat distribution, pressure requirements, and temperature rise. OEMs should evaluate the burner’s airflow specifications alongside the complete equipment design.
What should OEMs look for in an industrial gas burner manufacturer?
Important considerations include product compatibility, technical documentation, available burner configurations, engineering support, safety requirements, replacement parts, and experience with the intended heating application.
Industrial Gas Burner Solutions From Midco International
Choosing the right industrial gas burner requires careful consideration of heating capacity, airflow, combustion controls, equipment integration, and long-term reliability.
Midco International provides commercial and industrial gas burner solutions for OEMs and equipment manufacturers developing heating systems for a variety of applications.
Whether you’re designing a new make-up air unit, integrating a burner into industrial process equipment, or evaluating combustion technology for an existing product, selecting the appropriate burner is an important part of achieving dependable system performance.
Contact Midco International to discuss your OEM gas burner requirements and explore combustion solutions for your heating equipment.
